Pump Replacement Putnam County, NY
Most homes in Putnam County run on well water. When the pump dies, the water stops. There's no warning — you just turn on the faucet and nothing comes out. We've been fixing that problem for families here since 1960.
Most homes here have no backup — if the pump fails, you have no water. We replace submersible and jet pumps and check pressure tanks on every job Same-day and next-day appointments are available most of the time Our licensed plumbers pull the permits and handle the inspections for you
Sgns Your Well Pump Needs Replacing, Not Just Reiring
Dead water is the most obvious sign. You flip the breaker, wait, and still nothing. That's usually not a small fix.
We see these signs a lot when a pump is done:
No water at all, even after resetting the breaker The pump runs all the time but pressure stays weak A burning smell near the pressure tank or electrical panel The pump is 15–20 years old or more
In Patterson and Brewster, we pull pumps that have been in the ground since the Carter administration. That's not unusual here. Putnam County's housing stock is old, and a lot of those original pumps are still down there — until they're not. When a pump that old finally quits, repair usually isn't the right answer. We'll tell you straight when we look at it during our pump services.
Submersible vs. Jet Pump: Which System Putnam Homes Use?
Most homes in Putnam County have a submersible pump. It sits at the bottom of the well, underwater, and pushes water up to your house. Putnam County sits on granite bedrock, so most wells here are deep — according to the EPA's guide to private well components, submersible pumps are the most commonly used pumps for deep private wells, with the pumping unit placed inside the well casing and connected to a power source on the surface. That design is exactly what these wells call for.
Jet pumps work differently. They sit above ground — in a utility room or pump house — and pull water up from the well. If you have an older home in Mahopac, there's a decent chance you have a jet pump, especially if your well is on the shallower side.
Not sure what you have? That's fine. We figure it out when we get there and walk you through everything before we start.
What to Expect Before a Plumber Arrives for Pump Replacement
When you call, we'll ask a few quick questions. How deep is the well? How old is the pump? When did the water stop? That helps us load the right equipment before we leave the shop. It takes about five minutes.
A few things help the job go faster on your end:
Clear the path to your pressure tank and electrical panel Know where your main shutoff is if you have one Make sure the well cap is accessible if it's outside
We work in a lot of crawl spaces and pump houses in Carmel and Cold Spring. Some of them are tight. Some haven't been opened in years. If access is going to be a challenge, just tell us when you call — we come ready for it either way.
How the Pump Replacement Process Works, Start to Finish
We don't pull anything until we know what we're dealing with. First, we check the pressure tank, the wiring, and the well itself. That step matters — sometimes the pump isn't the only problem.
Here's how the job runs from start to finish:
We pull the old pump out of the well casing and check the drop pipe and wiring
The new pump goes in at the right depth for your specific well
All wiring and connections are checked and secured
We inspect the pressure tank and replace it if it needs to go
We run water at your fixtures and confirm everything is working before we leave
Putnam County requires a permit for well pump work in most towns. We pull it. We schedule the inspection. That's our job, not yours. Everything gets done to code and signed off properly.
Pressure Testing and Water Quality Checks After Installation
We test before we pack up. Pressure switch settings get checked and adjusted. We run water at the fixtures and make sure flow is where it should be. The job isn't done until that's confirmed.
Hard water is something we deal with on almost every well job in Putnam County. Mineral buildup, sediment, iron — it's in a lot of systems out here, especially in Garrison and the surrounding areas. A new pump install is a good time to take a look at what's actually coming out of the ground. The EPA recommends that private well owners test their water any time they replace or repair part of their well system — and a pump replacement is exactly that kind of moment.
We check for:
Sediment or discoloration in the water Iron or mineral buildup in the system Pressure tank charge and bladder condition
If something needs attention, we tell you before we leave. You'll know exactly what's there and what your options are. No surprises later.
How to Extend the Life of Your New Well Pump
A new pump isn't cheap. A little attention goes a long way toward making it last.
Watch your water pressure week to week. If it starts dropping or the pump seems to be kicking on more than usual, call us. Catching a small problem early is always cheaper than waiting.
Winter is hard on well systems in Putnam County. We've seen pressure tanks crack and exposed pipes freeze when a pump house wasn't properly insulated. Before the cold hits each fall, make sure your pump house is sealed up and any exposed plumbing near the well head is protected.
A few habits that help:
Get the pressure tank checked every few years Spread out heavy water use during dry summers — don't run the well dry Use a softener or filter if hard water buildup is a known issue in your area Keep your pump house above freezing all winter
We're happy to come out for a routine check between service calls. If you want us on a regular schedule, we can work that out.
FAQ's About Pump Replacement in Putnam County, NY
How do I know if my well pump needs full replacement or just a repair? No water, short cycling, or a burning smell near the panel usually means full replacement is needed. A licensed plumber in Putnam County can look at the pump, wiring, and pressure tank on-site and give you a straight answer.
How long does pump replacement take in Putnam County? Most submersible pump replacements take 3–5 hours from start to finish. Same-day service is available most of the time, so you're not stuck without water for days.
Do I need a permit for well pump replacement in Putnam County, NY? Yes, most towns in Putnam County require a permit for this work. We pull it and schedule the inspection — you don't have to do anything on that end.
Should I replace the pressure tank when I replace my well pump? If the tank is more than 10–15 years old or showing signs of waterlogging, replacing both at the same time makes sense. It saves you another service call down the road.
What's the difference between a submersible pump and a jet pump? A submersible pump sits inside the well casing underwater and pushes water up. A jet pump sits above ground and pulls water up — more common in older Putnam County homes with shallower wells.
How do I restore water pressure after a new pump is installed? We set the pressure switch before we leave and confirm flow at your fixtures. There's nothing you need to do — pressure is checked and confirmed before the job is closed.